1
USB Autoscope IV including:
USB 2.0 A/B interface cable, USB cable hanger, power supply cable
Automotive diagnostic oscilloscope
3
DIS Cx 6 capacitive probes
To get voltage waveforms from the high-voltage wires of the secondary circuit of distributor and distributorless ignition systems.
4
Sync synchronization transducer
To synchronize to a cylinder by attaching to a plug wire.
5
Cx-M universal capacitive probe
To get voltage waveforms from the secondary circuit of unshielded individual coils ignition systems, as well as from systems where the ignition coil is located inside the distributor.
6
Lx-M universal inductive probe
To get voltage waveforms from the secondary circuit of shielded coils of individual ignition systems, as well as from DIS-ignition coils mounted directly above the spark plugs.
7
Spark Gap high voltage spark gap tester
Is used in place of the spark plug when performing in cylinder pressure transducer testing. Also for ignition system testing.
9
Px35 in cylinder pressure transducer
Designed to measure the gas pressure in the range -0.95 … + 35 Bar (-14 – 508 psi). The main purpose of the transducer is to obtain the pressure waveform in the cylinder of the gasoline engine without combustion.
10
PxLonger M14 deep well adapter for high pressure (in cylinder) transducer
Is used to install the pressure transducer in cylinders where the spark plugs are deeply recessed.
For spark plug hole M14 х 1.25;
extension length 145 mm
11
Dx vacuum transducer
Designed for vacuum measurement of gases in the range -0.95 … + 0.15 Bar (-14 to 2.2 psi). The main purpose of the sensor is obtaining of the vacuum waveform in the intake manifold of the engine.
12
Universal cable (2 pieces)
Is used for connection to the USB Autoscope IV measuring adapters and / or transducers.
13
Measuring adapter (2 pieces)
For connecting of analog inputs 1 … 6 of the USB Autoscope IV to the car wiring (used together with a universal cable and probe).
16
Small alligator clip (2 pieces)
For connection of the measuring adapter with the vehicle wiring (without damage to the wiring, through the open terminals).
17
Insulation piercing probe (2 pieces)
For piercing wiring when performing tests. Causes minimal damage to the wiring. The piered wire should be sealed with a suitable sealer, however.
1
USB Autoscope Lite including:
USB 2.0 A/B interface cable
Automotive diagnostic oscilloscope.
2
Oscilloscope probe (4 pieces)
For connecting analog inputs 1 … 6 USB Autoscope Lite to the vehicle wiring.
4
Small alligator clip (2 pieces)
For connection of the measuring adapter with the vehicle wiring (without damage to the wiring, through the open terminals).
5
DIS Cx 6 capacitive probes
To get voltage waveforms from the high-voltage wires of the secondary circuit of distributor and distributorless ignition systems.
6
Sync synchronization transducer
To synchronize to a cylinder by attaching to a plug wire.
7
Cx-M universal capacitive probe
To get voltage waveforms from the secondary circuit of unshielded individual coils ignition systems, as well as from systems where the ignition coil is located inside the distributor.
8
Lx-M universal inductive probe
To get voltage waveforms from the secondary circuit of shielded coils of individual ignition systems, as well as from DIS-ignition coils mounted directly above the spark plugs.
9
Px8 in cylinder pressure transducer
Designed to measure the gas pressure in the range -0.95 … +6 Bar (-14 – 87 psi). The main purpose of the transducer is to obtain the pressure waveform in the cylinder of the gasoline engine without combustion.
10
PxLonger M14 deep well adapter for high pressure (in cylinder) transducer
Is used to install the pressure transducer in cylinders where the spark plugs are deeply recessed.
For spark plug hole M14 х 1.25;
extension length 145 mm
11
Spark Gap high voltage spark gap tester
Is used in place of the spark plug when performing in cylinder pressure transducer testing. Also for ignition system testing.
12
Dx vacuum transducer
Designed for vacuum measurement of gases in the range -0.95 … + 0.15 Bar (-14 to 2.2 psi). The main purpose of the sensor is obtaining of the vacuum waveform in the intake manifold of the engine.
13
Insulation piercing probe (2 pieces)
For piercing wiring when performing tests. Causes minimal damage to the wiring. The piered wire should be sealed with a suitable sealer, however.
14
Universal cable Lite (2 pieces)
Is used for connection transducers to the USB Autoscope Lite.
1
APPA 36T
Current transducer with two ranges of measurement:
±100A, where the output is 10mV/A.
±600A, where the output is 1mV/A.
4
Px8 in cylinder pressure transducer
Designed to measure the gas pressure in the range -0.95 … +6 Bar (-14 – 87 psi). The main purpose of the transducer is to obtain the pressure waveform in the cylinder of the gasoline engine without combustion.
5
PxLonger M14 deep well adapter for high pressure (in cylinder) transducer
Is used to install the pressure transducer in cylinders where the spark plugs are deeply recessed.
For spark plug hole M14 х 1.25;
extension length 145 mm
6
PxLonger M12 deep well adapter for high pressure (in cylinder) transducer
Is used to install the pressure transducer in cylinders where the spark plugs are deeply recessed.
For spark plug hole M12 х 1.25;
extension length 175 mm
7
PxFlex flexible extension M14/M12
The flexible extension can be used for diagnostics in hard-to-reach places.
It is supplied with adapters for spark plug threads M14x1.25 and M12x1.25.
The length of the Px Flex extension is 230 mm.
8
CTi-M
Current transducer
-50A…+50A (100mV/A)
with zero calibration button
Minimum measurable current 100 mA.
Maximum diameter of the measured conductor is 4 mm.
9
Laser
External optical crankshaft sensor.
Intended to diagnose using the script CSS of engines that are not equipped with a crankshaft sensor.
10
Paint Thickness Gauge
This gauge is used to detect the paint thickness on vehicle panels.
11
Dx Amplifier for vacuum transducer
To AC couple and amplify the waveform from the Dx vacuum transducer.
12
Spark Gap high voltage spark gap tester
Is used in place of the spark plug when performing in cylinder pressure transducer testing. Also for ignition system testing.
13
PD-4 transducer
PD-4 transducer used to detect pressure pulses
in diesel engine fuel rails. Suited for 4…6 mm fuel line
14
PD-6 transducer
PD-6 transducer used to detect pressure pulses
in diesel engine fuel rails. Suited for 6…8 mm fuel line
15
Piezo Amplifier (charge amplifier)
Charge amplifier is used to amplify
the signal from the PD-4 / PD-6 transducer
16
Universal cable extension
This extension lead is used when longer reach than what is provided by the normal test leads are needed.
17
PIN3-BNC
This adapter is used when it is desired to use test leads or equipment equipped with BNC connectors with USB Autoscope IV.
18
Adapter for high voltage extension cable
Designed for making your own coil or plug extension cables.
19
Ignition wire kit
Used when performing engine diagnostic tests. Allows you to take measurements with no or limited access to spark plugs. Used in conjunction with adapters for high voltage extension.
20
Remote Power Off
The remote fuse switch is used when it is required to shut off the engine without turning off the ignition switch. It is used during various tests of the engine (CSS and Px) and its systems.
21
COP Adapter
COP Adapter (Coil-on-Plug adapter) is intended for diagnostics of ignition systems using an oscilloscope. It allows you to display on the screen of an oscilloscope voltage pulses in the secondary circuits of all individual ignition coils of a modern gasoline engine at the same time, together with the synchronization signal of the first cylinder.
22
Lx4 / Lx8 – Inductive probes
The Lx4 inductive probe kit consists of four probes. The Lx8 inductive probe kit consists of eight probes. The black probe is installed on the COP coil of cylinder number one or the timing cylinder.
23
DIS Adapter
DIS Adapter (Distributorless Ignition System Adapter) is intended for viewing the secondary ignition parade on the screen of an oscilloscope on engines where the ignition coils with two high-voltage leads are used as well as on engines equipped with a distributor ignition system.
24
Oscilloscope probe (4 pieces)
For connecting analog inputs 1 … 6 USB Autoscope Lite to the vehicle wiring.
25
Universal cable Lite (2 pieces)
Is used for connection transducers to the USB Autoscope Lite.
26
USB2.0 АМ-ВМ Cable
The USB2.0 AM-BM cable is designed to connect an automotive oscilloscope to a computer USB port.
Model: Cablexpert USB2.0 AM-BM 1.8 m
Article: CCF-USB2-AMBM-TR6
Length: 1.8m
27
Viewcon USB3.0 AM/AF Active USB Extension Cable
The Viewcon VE057 USB3.0 AM/AF Active USB Extension Cable and USB 2.0 AM/BM Adapter can be used with any USB Autoscope oscilloscope.
Model: Viewcon USB3.0 AM/AF 5m
Article: VE057
Cable length: 5 m